Haiteng PETG Filament Blue 1.75mm 1KG 3D Printer Filament FDM 3D Printing Materials Blue Filament PETG Tougher Than PLA Filament
- New arrivals:Haiteng PETG Filament.
- Less Warping,Better Layer Adhesion,Bubble-Free.
- Recommended Nozzle Temperature: 230°C -245°C;Recommended Printing Speed:30-45mm/s.
Original price was: ₹ 1,699.00.₹ 999.00Current price is: ₹ 999.00.
Best deal at: 
amazon.in
Buy for best price
amazon.in
Haiteng PETG Filament Blue 1.75mm 1KG 3D Printer Filament FDM 3D Printing Materials Blue Filament PETG Tougher Than PLA Filament
Original price was: ₹ 1,699.00.₹ 999.00Current price is: ₹ 999.00.
Description
Additional information
Price History
-
Reviews (6)
6 reviews for Haiteng PETG Filament Blue 1.75mm 1KG 3D Printer Filament FDM 3D Printing Materials Blue Filament PETG Tougher Than PLA Filament
Show all
Most Helpful
Highest Rating
Lowest Rating
Add a review
Related Products
Liyo –
Good Products. Good quality Product, Printing Quality is too good….just Printed some Props
Sambit Pradhan –
Good but trouble with ender3. Really nice product with good strength and less amount of stringing but causes extruder jams if extraction is too much as it bends and gets stuck too easily
Liyo –
Amazing quality at such low price. First off, this is my first time printing with PETG. I usually use PLA, but this PETG by Numakers was so easy to print. It worked flawlessly the first time at nozzle 240 and bed 80 degrees.Packaging was great too, no damage and it came in a ziplock bag which was vacuum sealed very nicely!
muralivijay –
Amazing PETG, did not expect this. I was skeptical about this filament, but decided to take the risk, checked the settings on numakers website and they had very conservative settings like volumetric speed of 8. Decided to run flow rate test, temp towers, pressure advanced etc. Temp tower showed best bridging at 255, then did a flow rate test at this temp and got around 17 mm3/sec. So decided to change the Generic petg filament profile to 16mm3/sec.Bed temp was constantly at 70 and did not see any adhesion issues. Did use glue stick to make it simpler to remove.Modified a standard 0.2 print profile for 40 and 80 initial layer and initial layer infill. Rest were default settings.This filament prints really fast. I will be easily able to use sport mode on the P1S for any of the faster prints.Comes sealed in an aluminium lined bag. So there is a lesser chance of it being moist. But if you see any issues with the print, please dry the filament. It makes a world of difference.The speeds I am able to print this filament at is amazing.
Habeel Rashid Bakshi –
Amazing PETG, did not expect this. I was skeptical about this filament, but decided to take the risk, checked the settings on numakers website and they had very conservative settings like volumetric speed of 8. Decided to run flow rate test, temp towers, pressure advanced etc. Temp tower showed best bridging at 255, then did a flow rate test at this temp and got around 17 mm3/sec. So decided to change the Generic petg filament profile to 16mm3/sec.Bed temp was constantly at 70 and did not see any adhesion issues. Did use glue stick to make it simpler to remove.Modified a standard 0.2 print profile for 40 and 80 initial layer and initial layer infill. Rest were default settings.This filament prints really fast. I will be easily able to use sport mode on the P1S for any of the faster prints.Comes sealed in an aluminium lined bag. So there is a lesser chance of it being moist. But if you see any issues with the print, please dry the filament. It makes a world of difference.The speeds I am able to print this filament at is amazing.
Shivam k. –
VFM. At first I had issues due to the packaging but after that spools came well packed, layer adhesion is improved, quality is equivalent to European filaments after using 4+kgs of PETG from NuMakers I can say that it is one of the best VFM filament out there.